May 29, 1997 RADMOD - Version: 1.1 1996/01/19 A preprocessor to the program MODFLOW for simulation of axisymmetric problems For assistance, enhancement requests, or bug reports contact the Hydrologic Analysis Software Support Team via email at h2osoft@usgs.gov. See the file doc\radmod.txt for descriptions, references, and additional contacts for this software. Instructions for installation, execution, and testing are provided below. This version of RADMOD is packaged for use on personal computers using the DOS operating system. The installation procedures and the compiled version of RADMOD must be run using either DOS directly or a DOS window within Microsoft Windows, Windows 95, or Windows NT. TABLE OF CONTENTS A. FILES B. EXTRACTING FILES C. COMPILING D. INSTALLING E. RUNNING THE SOFTWARE F. TESTING A. FILES The following self-extracting DOS distribution files (containing the software, test data sets, and information files) are currently available. radm1_1.exe - Compiled using Lahey Fortran 90 with source code radm1_1b.exe - Compiled using Lahey Fortran 90 (binaries only) radm1_1s.exe - Source code only Included in directory radmod_1.1\doc is a Portable Document Format (PDF) version of the RADMOD documentation (ofr96659.pdf). A PostScript version of this report is available from: http://water.usgs.gov/software/radmod.html The PDF file is readable and printable on various computer platforms using Acrobat Reader from Adobe. The Acrobat Reader is freely available from the following World Wide Web sites: http://www.adobe.com/ http://www.shareware.com/ and by File Transfer Protocol (FTP) from the following site: ftp.adobe.com (path: /pub/adobe/acrobat) B. EXTRACTING FILES For whichever RADMOD distribution file that you have acquired, radm1_1.exe, radm1_1b.exe, or radm1_1s.exe, the directory radmod_1.1 is created (or overwritten) when the files are extracted. If the radmod_1.1 directory already exists, you may want to delete or rename it before extracting the files. The following are the steps to extract the files from a distribution file. Note, replace with the drive letter where you want to install RADMOD and optionally replace [directory] with the name of a directory on that drive: 1. If you are not in the directory where the distribution file is located, go there. For example (if already on the C disk drive): cd c:\wrdapp 2. Extract the files using the command: radm1_1 -d -o :\[directory] Substitute "radm1_1b" or "radm1_1s" for "radm1_1" if you are installing the executable-code-only or source-code distributions, respectively Note, be sure to include the -d (restore directory structure) and -o (overwrite existing files) options and ":\" in the command. Examples are: radm1_1 -d -o c:\ radm1_1 -d -o c:\wrdapp The following directory structure will be created (the contents of each directory are shown to the right): radmod_1.1 ; copy of this readme file `-----bin ; compiled executable and Lahey error file `-----doc ; documentation files `-----src ; makefile and source code `-----test ; batch files to run verification tests `-----data ; standard data sets used in verification tests Notes: a) The executable is not included in the radm1_1s.exe distribution file. b) The source code is not included in the radm1_1b.exe distribution file. c) It is recommended that no user files are kept in the radmod_1.1 directory structure. If you do plan to put files in the radmod_1.1 directory structure, do so only by creating subdirectories of radmod_1.1. d) Brackets "[xxx]" are used to indicate optional arguments to commands. C. COMPILING The source code is provided in the radm1_1.exe and radm1_1s.exe distribution files so that users can generate the executable themselves. No support can be provided for users generating their own versions of the software. In general, the requirements are a Fortran compiler and a minimal level of knowledge of the compiler and the DOS operating system. As provided, the makefile and source code are optimized for use on a Pentium personal computer using the Lahey Fortran 90 compiler and supplied make program. To generate a new executable, do the following: 1. Change directory to the source directory: cd radmod_1.1\src 2. Modify the beginning of the file named makefile to correctly specify system-dependent variables: FFLAGS Fortran compiler flags FC Fortran compiler name LINKER Fortran linker name LNKFLGS Fortran linker flags 3. Use the make program to initiate compilation of the source code and installation of the software: make [BINDIR=directory_for_executable] See the Installing instructions below for an explanation of BINDIR. The make will: a. create the directory radmod_1.1\bin if it does not exist, b. compile the source code, c. place the executable (radmod.exe) in radmod_1.1\bin, and d. place a copy of the executable in BINDIR if specified. D: INSTALLING To make the RADMOD program accessible from any directory, the directory containing the executable should be included in the PATH environment variable. For example, you could add a line similar to the following to the AUTOEXEC.BAT file: PATH=%PATH%;C:\radmod_1.1\bin Note, substitute the appropriate drive letter and pathname if not C:\ as shown above. As an alternative, the RADMOD executable can be installed in a directory already included in the PATH environment variable. The makefile (input instructions to the Lahey make program--located in radmod_1.1\src) contains instructions to optionally place a copy of the executable contained in radmod_1.1\bin in a specified directory. Use the following two commands to do this: cd radmod_source_directory make install BINDIR=directory_for_executable For example: cd C:\radmod_1.1\src make install BINDIR=C:\wrdapp\bin Note, the makefile may need to be modified to be used with make programs other than the Lahey make program. E. RUNNING THE SOFTWARE **System Requirements** - 386-based or higher personal computer with math co-processor running DOS. - 2 MB application RAM - 1 MB disk space RADMOD has been compiled using the Lahey Fortran 90 extended memory compiler version 3.00f. The file "LF90.EER" (from the Lahey compiler) located in radmod_1.1\bin contains error messages. If an error occurs, this file is used to print error messages if the radmod_1.1\bin directory is included in the PATH environment variable; if LF90.ERR cannot be found, the error will only be identified by number. After RADMOD is properly installed in a directory that is included in your PATH, the program is initiated using the command: radmod. The program prompts for the name of the file containing the input data for the RADMOD program and then for the names of the two output files (GFD and later grid spacing output). F. TESTING A test data set is provided to verify that the program is correctly installed and running on the system. The test may also be looked at as an example of how to use the program. The directory radmod_1.1\test contains batch files to run the tests. The directory radmod_1.1\data contains the input data and expected results for each test. Run the tests in the radmod_1.1\test directory using the command: test After the test is completed, the results can be compared to the expected results. To clean-up after the test, type the command: clean The test is described in the table below. Test is the test number, program is the program used to run the test, and the usage column indicates how a file is used, with i for input, o for output, and i/o for both input and output. test program description of test and files file name & usage ---- ------- ------------------------------------- ----------------- 1 RADMOD NEUMAN data RADMOD input file neuman.dat i GFD output neuman.gfd o lateral grid spacing output neuman.grd o * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Good Luck! * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *